Exactly How to Replace a Tub in Your Bathroom
Exactly How to Replace a Tub in Your Bathroom
Blog Article
On this page in the next paragraph you can locate additional helpful additional info in regards to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is readily accessible, the task can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and also place the new bathtub, the job is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also fit attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you may require an expert plumber to make tube links.
This post will aid you set up a brand-new tub in your bathroom if you have actually already acquired a new bathtub as well as don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the remaining water that will certainly originate from the pipes. When the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and also the sink. Safeguard the tap in place with the manufacturer offered backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical tap ports. The former type ought to be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Utilizing both wooden boards under its feet, put the bathtub in the called for placement. The wood boards are practical in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other faucet.
Turn on the supply of water and examine all joints and also new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has been used at the very least once as this will resolve it into its last setting.
Preparing for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall between the bath and also the tiling, leading to problems with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and also cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that blog entry on Tools You Need to Install a New Bathtub when browsing on the search engines. Do you know about somebody else who is looking into the subject? Why not share it. Thank you so much for taking the time to read it.
Book Today! Report this page